Updated 2023 to add the Bells of Steel rack and make several updates.
Table of Contents
Many of us are short on space in our garage, back room, or basement. A traditional power rack, or even an open-ended squat rack, takes up a painful amount of space.
In the past, your best option for space efficiency was to get a pair of portable squat stands.
3 problems with even decent portable squat stands like the above:
So it’s clear that we needed a totally different solution to save on space.
Behold! A folding squat rack that installs securely against the wall, folds out with the feet touching the floor for support, and folds back up against the wall for storage. Awesome stuff.
It can be installed either in a garage or in a room of your home. If you’ll be putting in rubber flooring, be sure to get that in before you install this. The height you install the rack at relative to the floor is critical. As a garage or basement squat rack, bare concrete can be just fine, depending on what else you have going on with your gym. Another advantage of these is you can get a really stable squat rack in a garage gym without drilling into your garage floor’s concrete to anchor it.
Note that some makers call these wall mounted power racks. Not so fast. A power rack encloses the bar on both sides and has safety bars. Technically these are just squat racks / half racks. It’s a marketing issue, I imagine.
The shared features among most of these racks are:
This basic idea was pioneered by PRx Performance in 2014, and backed by “Shark Tank” businessman and investor Kevin O’Leary in 2016. We sometimes make the mistake of thinking Rogue comes up with all this new stuff, but often they just popularize an existing idea by putting their huge market share behind it.
— Beware the details!!
There’s plenty to compare between the brands I’ve selected, and in this case they can’t be explained in a comparison chart. Read on or skip to my final recommendation at the bottom of this post.
| Model | Distance From Wall | Tubing | Folding Direction | Stringer | Starting Price |
|---|---|---|---|---|---|
| PRx Profile ONE | 24″ | 11-gauge 2″x3″ | Up | Yes | $649 |
| Rogue RML-3W | 9″ or 20.5″ or 40.5″ | 11-gauge 3″x3″ | Back | Optional | $595 |
| Titan Fitness T-3 v2 | 21.5″ or 41″ | 11-gauge 2″x3″ | Back | No | $380 |
| Titan Fitness X-3 | 21.5″ or 41.5″ | 11-gauge 3″x3″ | Back | No | $380 |
| Rep PR-4100 | 21.5″ or 41″ | 11-gauge 3″x3″ | Back | No | $500 |
| FringeSport | 25″ | 11-gauge 2.5″x2.5″ | Back | No | $548 |
| Bells of Steel | 20″ | 12-gauge 2.3″x2.3″ | Back | No | $400 |
Here’s what makes each rack stand out among the others. I’ll sum up the pros and cons of each one.
Here’s what happened. In 2014 PRx Performance invented and patented a wall-mounted rack design that lifts upwards easily via gas shocks to fold against the wall. In 2016 they aired on ABC’s “Shark Tank”, where investor Kevin O’Leary bought into 20% of the company.
However, before the Shark Tank episode even aired, Rogue and other companies caught wind of the innovation and began making their own but with an design where the left and right frame folds inward instead of the whole thing folding upwards, avoiding PRx’s patent.
Folding Mechanism
Unique gas shock system that makes it effortless to pull out and fold back, with locking pins to make it child-proof. All the fold-in designs below require you to remove the pull up bar and fold the rack parts sideways instead.
Pull Up Bar
3 options – None, regular, or extruded 36″ from the wall for kipping pullups. Get at least the regular. Everyone needs a pull up bar. Keep in mind the kipping bar does not fold back itself, so it’s going to be sticking out 12″ from the wall as you fold the rack in. For most of us that’s not really an issue, as we don’t need to save space that high.
Depth: 24″ from the wall, folds to 4″ from wall.
Design and Construction: 2″x3″ 11-gauge steel. The folding design forces a tad bit of play in some joints, making it not feel as solid as a comparable 2″x3″ rack. That goes for all similar wall mounted squat racks. They can wobble a little under loads.
505 lb was dropped on an earlier 3×3 version of this rack in the video below, ripping a screw out of the stringer. The issue I think is mainly how well you stringer is mounted into the wall studs with the chosen screws, but I also notice that the metal of the stringer appears to bend away from the wall a little bit, suggesting that it’s not the thickest steel. You see a lot of wobble in slow motion in the video, which isn’t necessarily a bad thing, the way flexing does help absorb the shock of the weight and keep the rack intact, not to mention reduce the risk of damage to your bar.
The above 3×3 rack is now sold as the Profile PRO. Besides the larger tubing, the Pro has several color options and another height option. But the Pro starts at $849, putting it even further outside the price range of competing racks featured here, so I’m mainly just featuring the less expensive (but still expensive) Profile ONE here.
You might notice that some of the Profile ONE pics show a lack of holes near the bottom of the uprights. Those are old pics. The latest version has holes going all the way to the floor.
| PROS | CONS |
|---|---|
| – easy installation – quickest setup – made in the USA | – highest priced – no depth choices |
PRx has also come out with a fold-in design like the competitors below, but I have chosen not to feature it here because it uses 14-gauge steel and is therefore significantly weaker than competitors. If you are curious, it’s the PRx Fold-In ONE Rack.
The folding racks are surprisingly hard to navigate to on Rogue’s site menu. You have to look in the Power Racks category, not in Squat Stands or Wallmounts where you would expect them.
The RML-3W has 3×3 tubing. They also have the 2×3 R-3W still. Rogue is moving away from their 2×3 racks, and I recommend their 3×3 racks at this point.
If you want a choice of (currently) 11 colors, the RML-3WC is the color-option version of the RML-3W, at a $100 premium.
Rogue’s 3×3 racks are 49″ wide, which makes it a tighter fit for your bar than 48″ or 47″ wide racks. Consider sandwich J-cups that stick out from the rack and gives you bar more side-to-side room for better safety when re-racking.
Rogue put Westside hole spacing on the uprights. What this means is 1″ on center between the holes in the height range you would use for bench pressing, to help you set the J-cups and safety bars in the perfect spot. Higher than that they are spaced 2″, which is fine for squats or overhead presses. This pattern of spacing was popularized by Louie Simmons of Westside Barbell, hence the name.
They have other marks on the uprights to help you put the two bar catches at the same height and not have to eyeball it too hard.
Folding Mechanism
To fold it away, you first remove the 2 pins above and pull off the pull up bar. Then pull 4 pins from the rack hinges and fold both arms against the wall. The hinges go both ways, so you can fold them both in, both out, or one in and one out, whatever works for your space, standing out only 5″ from your wall. If you have the wall space available where you can fold at least one side outwards, you won’t have to remove the J cups. Otherwise, not a big deal.
Accommodating Floor Slope
As Johnny Wild pointed out in the comments, the Rogue bracket design has some play to it, which is not sloppy design but is actually helpful for allowing you to lift the sides of the rack clear of the floor as you fold it in or out. In addition, if it didn’t have the play, the feet would be dangling 1/4″ off the floor if you fold it out towards your garage door, with the typical garage slope.
Pull Up Bar
Max height 87″, adjustable down via pop pins. Like the Titan and Fringe models, be conscious of what height you’re installing the top horizontal tubing against the uprights, because it will get in the way of your desired pull up bar height if you aren’t careful.
Depth Options
Choose from a 9″ deep, 21.5″ deep or 41.5″ deep option that you select on the product page. The 9″ is, in my opinion, too tight. The 21.5″ gives you enough room for squats, bench presses, and most any other racks exercises, giving enough room for your feet, head, and bench, as appropriate. For more space for dynamic pull up movements, you will want the 41.5″ deep. You could also fit Rogue’s 24″ spotter arms on the inside of 41.5″ deep version, if you have limited space when working out. The 41.5″ deep doesn’t fold in neatly to the wall and will overlap unless you fold them one in and one out, which takes up more wall space. Either way works, depending where you want to save the most room when folding it.
Color Options
While the RML-3W is the classic Rogue matte black, the RML-3WC version has powder coating in a bunch of color choices, even a satin clear coat that I’d love to see close up. Color choices are not available for the 2×3 R-3W rack. Rogue is getting away from its 2×3 racks and will likely discontinue them at some point.
Ryan (That Tech Teacher on youtube) has a great video going over the parts and installation in his gym:
A huge plus to Rogue’s folding rack is the $55 stringer option on the product page. You get those two steel backplates. They aren’t there to look cool. The stringers help you in two ways:
| PROS | CONS |
|---|---|
| – made in the USA – 2 depth options – 2×3 and 3×3 tubing options – stringer option (and a very nice one) – lots of attachments – color choices | – installation takes skill unless you get the stringer – folding procedure takes a minute – expensive |
Titan T-3 and X-3 folding racks are their 2×3 and 3×3 racks. There were a few iterations in design, and at this point the only difference between them is the tubing size. The T-3 is actually 50mm x 75mm, and the X-3 is 75mm square. This makes them a little smaller than 2×3 and 3×3, respectively. The Rogue Infinity and Monster Lite attachments will mostly fit well enough.
Titan’s racks are all 48″ outside width, meaning the 2×3 rack gives you 2″ of extra space inside than the 3×3. Some specs given on their site say 50″ width, but that includes things like brackets or feet.
The X-3 comes with two pairs of J-cups rather than one, and they are UHMW-lined unlike the bare steel J-cups included with the T-3.
| PROS | CONS |
|---|---|
| – Good price – 2 depth and height choices – Somewhat compatible with Rogue Infinity or Monster Lite attachments | – installation takes skill – No stringer available – Folding procedure takes a minute – Fat 1.5″ pull up bar only – Made in China – Typically a lack of attention to detail in the alignment and welds – Metric sized tubes are a little undersized for true 2×3 or 3×3 attachments |
Rep is the only manufacturer to offer a folding rack in a 3×3 only model. Why even bother making a 2×3 model when they’re beating Rogue on price?
The overall design is very much like the Rogue RML-3WC. It has a 48″ width, which is conveniently a little narrower than Rogue’s 49″ to allow for more barbell movement. 1.25″ pull up bar. UHMW lined J-cups and feet.
Laser-Cut Numbers
Here’s a good addition. Laser-cut numbers, starting from the bottom of the bench press area and going all the way up. These are valuable for getting your J-cups or safety arms set at the right height. Otherwise you have to start making your spots with tape.
The lack of a stringer option hurts a bit. You need to buy some boards at the lumber store. The stringer makes it so much easier to install, with no careful work required on screw hole placement.
Metric Sizing
Like Titan’s rack, Rep’s is not strictly a 3×3 rack. It’s 75mm, which is 2.95″, and metric hole spacing as well, ruling out any Rogue ML attachments that require a hitch pin in a second hole. The hole spacing is therefore similar to Westside but not Westside compatible.
| PROS | CONS |
| – Good price – Westside-like hole spacing – Somewhat compatible with Rogue Monster Lite | – Installation takes some skill – Made in China – Metric sized tubing and hole spacing |
Fringe has a 365-day return policy, which I think is the most generous in the whole industry right now. You get free shipping to begin with, and then you can send it back within a year, on a whim, and get all your money back. Or within 30 days and they’ll even pay return shipping. Evidently they don’t get many returns, or they wouldn’t be able to do this.
Fringe split the difference and did 2.5″ square tubing instead of 3″ square or 2″x3″.
They kind of priced themselves out of the market. For the price, you would be better off getting a Rogue rack that has more attachments available, a stringer option, and better resale value.
Pull Up Bar: The pull up bar can adjust from 70″-88″ from the floor (5’10” – 7’4″). It’s 25″ from the wall.
Width: 49″ wide, the same as Rogue, the maximum width you want for a rack.
Depth: 25″ from the wall.
Folding Mechanism: Just like Rogue. Fold either side in or out. It takes the same amount of work, pulling out 4 pins for the pull up bar and 4 for the rack hinges. Like Rogue, you can leave the J cups in place if you’re folding at least one side outward.
| PROS | CONS |
|---|---|
| – 1 year return policy and 30 day free return shipping | – installation takes some skill – no stringer option – folding procedure takes a minute to do – no depth choices – made in China – expensive compared to others – incompatible with other brands of attachments |
The latest addition to this list! Somehow I overlooked it until 2023. They came out with it in 2019 and have gathered plenty of excellent reviews.
Compatible with Rogue Stringers
As with other racks, they recommend you install a 2″x10″ wood stringer on the wall to bolt this rack into. The crazy thing is the Rogue stringers fit this rack, no mods needed, if buying them is easier for you or you like the look. If you find another rack also fits the Rogue stringers, please leave a comment!
Smaller Style
This rack sits 20″ away from the wall. Functionally the 20″ vs 21.5″ on some other racks here should make no difference for you, except for the possibility of not getting a particular bench in incline position into place. This 20″ depth makes it possible for the rack to have a 47″ overall outside width, which gives you plenty of wiggle room for safety when re-racking. Because the tubing is only 2.4″ square, you also should have plenty of hand room even for extra-wide grips. These dimensions in my opinion were an excellent design choice by BoS to make them stand out.
Like the Titan and FringeSport rack, Bells of Steel sizes this in metric. In this case it’s 2.3″/60mm square tubing, with 14mm hole spacing. making it incompatible with attachments from any other racks except a few others by Bells of Steel. The tighter hole spacing in the bench press area, like some other metric racks, is similar to Westside style.
| PROS | CONS |
| – Good price – Westside-like hole spacing – Fits the Rogue Folding Rack stringer – 47″ outside width | – Installation takes some skill – Made in China – Metric sized tubing and hole spacing |
Like certain other designs of racks, wall mounted squat racks are not made to fully handle loads that can be placed on spotter arms hanging off the front.
The above shows why. A barbell this far out from the support leg of the rack will cause what would ordinarily be a “tipping” force to the rack. Because this type of rack is attached to the wall, it can cause the screws in the top bracket to rip right out of the wall.
A stringer across the wall studs helps, whether it’s wood or steel, the way it has several screws securing it to multiple studs in the wall. Even then, no guarantee the screws won’t still rip out.
Realistically, I have heard from someone who does rack pulls on the spotter arms on such a rack. The closer you have the barbell to the uprights, and not far out like I have in the diagram, the more the support leg takes the force and the less the wall attachment point does. But as discussed already, even up against the upright you’re away from the center of gravity of the rack and you’re putting some force on the wall attachments.
The main issue with the ~21″ deep racks is they might restrict the exercises you can do. Some adjustable benches have feet or wheels that will stick out too far back in the incline position, putting the wall in the way of getting it into place. However, it looks like many benches, and the Vulcan adjustable bench for sure (Thanks Robert for the comment on this), will work in a moderate incline with the 21″ deep racks.
The tight fit is even more the case with another rack I want to bring to your attention, the Rogue Monster Lite Slim Rack pictured above. The front face of the uprights are a mere 14″ from the wall. I’ve determined that the 14″ gives you enough head room from the wall to allow for back squats, with a few inches of head clearance from the wall. Assuming that your bench’s feet don’t stick out past the bench pad too far (most modern benches are pretty good about this), you can do flat bench presses. Unlikely you can do incline bench presses with this unless you have something like the BodyCraft F704 bench (or discontinued BodyCraft F320 bench) that slides back for incline.
Anyway, the Slim Rack might work even better than a folding rack for you, if you don’t mind being close to the wall and you don’t need a rack that folds tighter against the wall to be out of the way. It will feel more solid than a folding rack because it has no moving parts.
Rogue wins! Here’s why…
Quality
Rogue’s quality is the highest and most consistent. Titan for example does ok with some things, but this rack needs to be all perfectly aligned so that you can install it with nothing weird going on in its stability, connections, and fold-up procedure. Titan cuts corners with design to lower the price. I trust Rogue the most with having everything made right. Rogue sells more of these types of units than anybody else, and in their own factory in Columbus, OH, while other companies outsource to China and aren’t able to unpackage and inspect most of the units.
Stringer Option
If I were in the market for a rack like this, the lack of a stringer on the other models is the dealbreaker. It assists in a big way with installation and stability. Granted it costs $105 for the stringer pair.
Price
Great price, especially for what you get. PRx is ridiculously priced.
Distance from Wall
The minimal distance from the wall, 21″ or so, makes sense for any folding rack. The whole point is to save on space by folding it in as tightly as possible, and the 41″ folds up poorly, eating up tons of wall space or sticking out a couple feet if you fold both sides inward.
Attachment Options
Being as this is an Monster Lite rack, Rogue’s Monster Lite attachments will fit this rack. Some attachments are made for full power racks. Some appropriate ones would be the landmine base, rope anchor, and many more. That opens up a options for more exercises and even more efficient use of space. Unlike the 2×3 Infinity racks, Rogue won’t be moving away from the Monster Lite racks for the foreseeable future, so you’ll have good compatibility moving forward.
Rogue basically offers so many of the best features of these racks that it’s an easy choice.
Rep’s folding rack is nearly an exact copy of Rogue’s. UHMW lined cups and feet, quick attach pins, 1.25″ pull up bar, etc.
Rep is known for making good equipment, nearly on par with Rogue’s quality and attention to detail, not cutting corners, and at a lower price. They can’t quite meet Rogue’s quality, because their equipment is made in China and subject to spot inspections when they get them instead of constant inspection of each piece by their own employees. Rep makes sense as a second choice behind Rogue. You save about $300 over the RML-3WC.
Rep’s rack is somewhat compatible with Monster Lite attachments. Their 75x75mm tubing is a hair smaller than 3×3″, making all Rogue attachments fit with a little play. The hole spacing Rep uses is also metric, ruling out attachments that have to be secured with a safety pin. These issues force me to have the opinion that Rep is not the best choice here.
Laser-Cut Numbers
One significant addition over Rogue is their laser-cut numbers, starting from the bottom of the bench press area and going all the way up.
Too bad they missed a stringer option. If you like working with wood, this might be a non-issue for you. You will certainly save money by putting in your own wood stringers, as shown below.
View Comments
A hidden issue on these racks are safety spotter arms -- dropping a loaded bar on them can rip the rack out of the stringers.
As I recall, some manufacturer's tend to prohibit them or limit their length to 6-12" similar to squat stands. I think one allowed an 18" and no one recommended 24".
One person told me he put on 24" spotter arms on his Titan X-3 folding rack and does rack pulls on it. I assume he does it as close to the uprights as he can, or at least I would. He has steel stringers (which Titan used to sell and maybe will again) lag screwed to the studs. I saw Rogue's warning on the spotter arms. I can see how it's very questionable.
Anyway, good thoughts, I'll have to add this to the article in the next update!
The specific scenario I balk at for these racks is missing a low bar squat -- where the bar hits will under far less control than say a rack pull or even a missed bench.
Keep up your great articles David!
Yeah I imagine something interesting has happened with that a few times and just hasn't been caught on video yet, other than the Prx rack test.
Wright Exercise has some very interesting space saving garage gyms. So does Pure Strength slim gym. Bridge built has their Pheonix squat stand. And Texas Strength Systems has a really nice competition style squat stand that can break down for more room. All of those options are made in America and support small businesses
Thanks, I'll look into those and see if I can get them added somewhere.
Hey, I posted about the Rogue stringers working with the T-3 folding rack. I got tired of the 50” width and discovered that the Rogue Socket pull up bar with the Infinity sockets combined with the Rogue stringers makes the Titan 47”. The socket pull up bar is drilled nearly all the way through the bar for its mounting screws so its ultra safe. It only takes a minute to insert the bar into the sockets and tighten the 2 screws, nearly as fast as the original bar, which I can still use, just below the socket mounts.
I bought mine from the boneyard, so it ended up being $114 shipped including the Infinity sockets. I also bought two longer standard 3/4 bolts from home depot for 27c each to make it easier to install. Anyway, it looks great with an orange bar and functionally much better than 50” width.
How does the T-3 rack connect to the Rogue stringers hardware wise? I have ordered the stringers (not here yet) and can't get a detailed view on how the Titan rack would mount to them. Can you no longer use the included Titan pull up bar when you do use the Rogue stringers? Thanks in advance, sorry for all the questions.
I don’t remember if the T3 or the stringers had the bolts needed but one or the other has them. Use the outer of the two sets of holes on the stringer. It’ll seem a little off, but tightens up right. You can use your titan pull up bar.
Wow, you were not kidding about getting those in the outer holes of the two stringers. Got the T-3 rack set up with Rogue stringers, but since Titan is a 50" width and Rogue is a 48" standard, the Titan pull up bar does not quite fit. May try the Rogue socket bar like you suggested. Also, just for information to others who attempt this, the rack folds somewhat on top of each other due to the extra 2" in length on the Titan rack. The Titan rack doesn't fold completely flat in the Rogue stringers, but close enough and worth it for ease of installation. If I had it to do again, I'd just go all Rogue and be done with it as I prob spent way too much time trying to save a buck.
Hmm, something isn’t right, mine folds completely flat and i can use the original pull up bar. I have the 41” T-3 V2.
After looking at the bolts mounting the rack to the stringer, they must be Rogue as they are silver and Titans bolts are all a gold tinge.
Hey, bro. Great info to know about the Rogue stringers working with the T3. Any thoughts on working with the X3? Should be the same, no?
Rogue's shipping is higher than PRX. Once you include shipping, the prices are almost identical for the Rogue RML-3W Fold Back Wall Mount Rack vs the PRX Profile with Pull up Bar. Any preference if the prices are almost the same?
Rogue has 4 pins that you need to put in to lock and take it off to unlock. Doing this before and after workout could become a *chore* if you're also vertically challenged (at least for the top ones). Also, if you have J-cups and Pull up bars installed, you will need to take all of this off. With the PRX, it takes 10 seconds and no need to take off the pull up bars or the J-cups.
Another issue is the rogue scrapes your floor (opening and closing). With PRX, you avoid that too. With garage floor slopes, that could be another problem.
I am in the market, and these are the things I could think of for my situation.
I wish PRX pricing wasn't so high, but, with the COVID situation, it is only going higher.
Thank you for the article! It's very practical in 2020 and I'm about to own my first house in August. Do you have any opinion on the RML-90SLIM by any chance? I'm set on getting Rogue Fitness but would like to know their newest model.
I've been looking at the RML-90SLIM rack a bit. Near as I can figure, there's enough space from the wall to give you head room for flat bench presses or low bar back squats, by just a couple inches. I bet they figured the same thing.
Rogue's racks are all fairly new or updated models, with the way they sell such high volume and get things upgraded or replaced pretty quickly as features improve. That particular rack is the only one compact against the wall like that, other than the folding racks.
Thanks for the info! That was really helpful and even the additional updates are great.
First off thanks so much for the great info. I am going to pull the trigger on the Rogue one but do have a question. Is the 21.5" depth enough space to slide a bench to do incline chest presses?
Good thinking. That could be a problem with some benches for sure, especially at the higher incline positions. It'll be right around the range of maybe fitting, maybe not. The only one I can think of offhand that is designed to fit into a tight space like this is the BodyCraft F320, the way the seat slides back as the backrest inclines. I'll have to add a note about this.
Thanks David. Looks like the F320 is perfect.
UPDATE
The Rogue folding rack with the 21.5" depth is plenty for incline bench press.
I have the Vulcan adjustable bench and it works perfect. I am very happy with my purchase. You get what you pay for and Rogue is pure quality. I also purchased the air bike.
That's great that it all fits well enough for incline!
Hi David
Great comparison and review!!!
I am looking at the Rogue one and I have hard time estimating the folding on the 41.5... how much space (from the wall) it takes if fold in?
My issue is that my wall it small and i fear I would hit the perpendicular wall when I rack the bar on the 20.5 but the folding issue of the 41.5 may also be a. Issue
If you visualize it, the sides will overlap, so maybe 8" or so from the wall?
I've been trying to figure this one out as well. I don't think it'll be a mere 8" from the wall. TL;DR it's a problem unless the product is redesigned.
If you think about it: first swing one side inwards, let's say the left side just for this example. The left side's vertical post is now maybe 1-2" from the right side's hinge point, and normally the inner aspect of the right side would lay (nearly) flat to the wall, if the left side that you just finished folding in weren't already in the way.
But it's in the way now. You start to fold in the right side, at which point the horizontal (41.5") tubing will start to impinge upon the now-folded-in left side's vertical post. (Imagine the left side's post rubbing the paint off the right side's 41.5" bar somewhere close to where the right side's hinge point is, long before you're able to swing the right side anywhere approaching a satisfactorily "closed" position.)
If it were possible to easily dislocate/disassemble the right side's hinge point, then yes, you'd be able to lay the right side flat against/overtop of the left side, for the estimated net distance from the wall of 8". But the hinge point isn't a quick release design, and repeated disassembly/reassembly of the hinge point would be annoying at the very least (and I'm guessing would cause unwanted wear/fatigue of the threads over time, if you were committed enough to want to do this every time).
My biggest need for going with the 41.5" tubing is to provide more room for kipping pull-ups. One alternative approach I've considered is to get a pull-up bar attachment which adds some distance from the wall, something which supplements or replaces the existing pull-up bar of this rig. Except in this context, I don't think Rogue makes one. They do make a few different pull-up bars, but nothing which could be easily pinned into place which helps to provide more space from the wall. (They do offer a couple of flying pull-up bars, but those designs are a) permanent, not removable, and b) would add far too much height to be able to fit in my garage with a 100" high ceiling.)
Another design to consider (one which Rogue isn't offering, but bear with me on this thought experiment) would be if one side (let's say the right side, to continue the example) had a hinge point which was mounted to the side (left side) of the 41.5" tube, rather than going through the center of it. Now you've got something closer in design to how the doors in your home work, ie, when you fold the right side inwards over the left side, it would create a bit more room near the apex of the angle. (If the doors in your home had a hinge point going through the middle of the door, you'd hear a 'crunch' anytime you opened a door more than 90º. Actually, unless the corner of the door was rounded off, you'd hear a 'crunch' the first time you went to open the door. But I digress.)
For best results, the hinge point would probably need to be roughly the distance equivalent to the thickness of the tubing. But for best stability when unfolded, that same hinge point would probably benefit from having something on the opposite side of the tubing (something which is solidly secured to the stringer) that you could drop a pin into, once unfolded. (I feel like I'm trying to reengineer the design here. Hmm.) It would add cost to the product, but you'd get more compactness when folded. To save money, only do this to one side of the rig and stick with the current design on the other side.
Let me know if you end up getting a chance to try out one of these rigs with the 41.5" tubes, and how it goes when you fold them onto each other.
Thank you for the great information on your blog. You stated that the Rouge RML is "40.5″ deep doesn’t fold in neatly to the wall and will overlap unless you fold them one in and one out, which takes up more wall space."
My question is how much actual wall space will it take if you fold them both to one side ? I love the Rogue product and would like to know if it will fit within my "wall space" parameters.
Add the overall width plus the depth and that should give you a pretty good idea. Around 101" for the 40.5" one.
Thank you for the very informative site! So just quickly, I read that the Rogue stringer will fit the titan rack. So does that mean the Titan stringer will fit the Rogue rack? My Rogue wall mount rack is coming in, I don't want to use wood and I can't get my hands on a rogue stringer, but I can get a Titan stringer. Does anyone know? Thanks
It says above that the Rogue Stringers work for the Titan T3 but I'm wondering how that is possible if the T3 is wider than the Rogue racks? Wouldn't the spacing on the Rogue Stringer where you mount the rack to the stringer be too narrow and create an angle when you open it up to connect the pull-up bar?
It has a slight angle, but everything works. Also see my latest comment about using the Rogue socket pull up bar.
I just received rogue stringers and titan t-3 folding. The brackets for rack are too wide for the holes on the stringers. Now I’m left with stringers from rogue and trying to sell them
Were you able to get the Rogue stringer to work with the T-3? It looks like the T-3 changed some over time. Maybe that is why it didn't fit? I have the t-3 21.5 but need to get stringers. Hoping to get the Rogue, but if it doesn't fit, there's no point.
They fit, but as I've said before, its very tight. - Unless Titan changed their T3. I had this setup for about a year, worked great.
Hopefully Titan has them again. I also wonder if they will ever have the X-3 folding racks again. A few months ago they assured me it isn't discontinued, but here we are.
I don't know how, but it fits according to Johnny Wild's comment here. (I originally had his name wrong - I must have been thinking of the UFC fighter!)
https://www.tworepcave.com/3006/power-rack-attachments-compatibility-master-list/#comment-8606