2026 Update – Revamped entire guide to link to manufacturer pages that list all compatible attachments, so that you can quickly browse the full selections.
You get a hold of a great power rack or squat rack, but then you find out that the company doesn’t make the attachments / accessories that you want.
No problem! You should be able to find a compatible attachment or accessory, as long as your rack is made with one of a few standard configurations.
Table of Contents
The key specs are:
The tubing size of the uprights, as above, typically one of: 2″x2″, 2″x3″, or 3″x3″.
Racks made in China usually use metric sizing. This applies to a lot of brands featured here. They don’t advertise the fact, and you would have to ask them or run into the problem yourself. The tables they are organized in identify them as such.
The hardware/peg diameter that fits into the holes in the uprights, as above. Varies from 1/2″ to 1″. Going by the peg diameter is more consistent across brands than the hole size that is cut somewhat larger than the peg.
The hole spacing in the uprights, ie: the distance between holes on center, as above. This is only applicable for attachments that use 2 holes, the second using a locking pin.
2″ spacing is becoming the standard. Some racks have Westside spacing, which is 1″ spacing at a certain height range for setting bench press safety bars just right, and otherwise 2″ spacing above and below that.
An attachment can fit in a larger hole than it’s made for, but it will be able to wiggle and maybe tip down a little, depending on the snugness of the bracket that goes over the tubing.
Similarly, attachment brackets can fit onto slightly smaller tubing than what they were designed for. This can be less bad than the wrong peg size, because you can glue shims (UHMW plastic or wood) to the inside of the attachment’s bracket to make it fit. Some attachments work well enough even if they’re loose. Some don’t have enough pressure put on them to be a safety issue, like a battle rope anchor, but it could still rattle.
Lastly, the steel gauge (wall thickness) of rack tubing does not factor into compatibility. The tubes are fabricated to an outside diameter spec.
For fitting 3×3 attachments onto 2×3 tubing, or 2×3 attachments onto 2×2 tubing, an Etsy seller is making these adapters to fill the void in the bracket.
I don’t recommend you use load-bearing attachments that don’t fit quite right, such as J-hooks, steel safety arms, or plate holders, unless you have a good way of retrofitting it to be snug enough. Use some common sense, visualize it, and you’ll get the idea.
In many cases attachments that use a locking pin to secure the attachment into a second hole on the rack’s upright won’t line up the same on all racks. Normally this is the difference in metric and imperial (inches) hole spacing. As much as you want it to work, under most circumstances you won’t get the locking pin in. The offset starts at 1/16″ per hole and widens cumulatively.
If you’re thinking of foregoing the locking pin or buying a thinner one, and you have to ask for confirmation on whether it’s safe, you probably shouldn’t do it.
Rogue has among the best and most consistent quality. Cheap Amazon-only brands are the worst and might be unsafe, and we avoid promoting them when possible. Most other brands are somewhere in the middle or sometimes as good as Rogue.
Size categories ordered smallest to largest.
Titan X-2 (discontinued)
Discontinued size. The Titan T-3 Multi Grip Pull Up Bar is compatible with this rack (thanks TJ!).
Granite Fitness Series 22 racks (discontinued)
Powerline PPR1000, Northern Lights Crossbox (discontinued)
| Attachments List | Popular | Notes |
|---|---|---|
| Powerline attachments | – U-Link / Rope Anchor – T-Bar Row Attachment / Landmine – Weight Plate Horn | See the Options links on the PPR1000 product page. They aren’t organized well anywhere else. |
Titan Fitness T-2, Giant Lifting 2X Series
50mm is a hair smaller than 2″. These are generally compatible with 2×2 racks. However, 2×2 attachments using a second hole and hitch pin are incompatible.
This size is considered a “budget” rack, so there are typically only a few attachments.
| Attachments List | Popular | Notes |
|---|---|---|
| Titan T-2 Series attachments >> Amazon prices are lower in some cases. | – Landmine – Spotter Arms – Dip Bars – Weight Plate Holders | |
| Giant Lifting 2X Series attachments (use code TWOREP for 5% off) | – Mag Pins – Landmine – J Cups |
Powerline PPR200X / PPR500, Best Fitness BFPR100, Valor BD-7 / BD-33, Rep Fitness PR-1000 / PR-1050 / PR-1100, Fringe Garage Series Squat Cage, Legend Fitness Varsity Series, Get Rx’d Pro Power Cage, Vanswe Power Rack, TDS 1000lb Power Squat Rack, Fitness Reality 810XLT, Mikolo Fitness F4 / K6, Amstaff PR100 / DF1161A / TP006D (discontinued)
This size is considered a “budget” rack, so there are typically only a few attachments, and some manufacturers don’t seem to offer any.
| Attachments List | Popular | Notes |
|---|---|---|
| Rep Fitness PR-1000 Series attachments | – Spotter Arms – Weight Storage – Dip Station – Landmine – Sandwich J Cups | |
| Fringe Garage Series attachments | – Mammoth Belt Squat – Weight Storage – Spotter Arms | |
| Synergee Fitness attachments | – Plate Storage – Safety Arms – Dip Handles | |
| Valor BD-7/BD-33 attachments | – Dip Handles – Spotter Arms – Weight Plate Storage | |
| Mikolo Fitness attachments | – Lateral Raise – Leg Extension & Curl – Lateral Raise & Chest Fly – Magnetic Hitch Pins | Look for 2×2 in the title. |
ForceUSA MyRack only.
60mm is 2.36″, way off from all imperial sized racks. These attachments might fit the metric racks in the next section well enough that take 16mm pegs.
| Attachments List | Popular | Notes |
|---|---|---|
| MyRack attachments | – Safety Slings – Monolift – Dip Handle – J Hooks Pro – Landmine |
Bells of Steel Residential Rack / Utility Rack / Light Commercial Rack / Brute Rack / Folding Rack / Combo Rack
60mm is 2.36″, way off from all imperial sized racks. Some attachments in the 13mm peg section above might fit well enoough.
| Attachments List | Popular | Notes |
|---|---|---|
| Bells of Steel strength attachments Bells of Steel weight storage attachments | – Seal Row Pad – Y-Dip – Spotter Arms – Landmine – Sandwich J Cups | Look for the 2.3″ size option on the product pages. |
Powertec WB-PR / P-PR (discontinued), Hulkfit Power Cage
60mm is 2.36″, way off from all imperial sized racks.
| Attachments List | Popular | Notes |
|---|---|---|
| Powertec attachments | – Premium J Hooks – Spotter Arms – Weight Storage | Look for ones that fit 2 3/8″ uprights per the product descriptions. |
Valor BD-11 / BD-41, Amstaff TR023 (discontinued) / TR025 (discontinued) / SD1050 (discontinued)
| Attachments List | Popular | Notes |
|---|---|---|
| Valor BD-11/BD-41 attachments | – Dip Handles – Spotter Arms – Weight Storage |
Titan Fitness T-3 / T-6 (discontinued)
Slightly smaller than 2″x3″, and pegs slightly larger than 5/8″. Generally compatible with 2×3 racks except for attachments using a second hole, because of the metric hole spacing.
| Attachments List | Popular | Notes |
|---|---|---|
| Titan T-3 attachments >> Amazon prices are lower in some cases. | – Safety Spotter Arms – Safety Straps – Safety Strap Spotter Arms – Dip Bars – Weight Plate Holders | |
Rogue Infinity (R-Series), FringeSport Kip Power Cage / 2×3 rigs (discontinued), Bolt Fitness Lightning Power Racks, Synergee Fitness 2300 Series
| Attachments List | Popular | Notes |
|---|---|---|
| Rogue Infinity attachments | – Speed Bag Platform – Battle Rope Anchor – Matador – Spotter Arms | They have focused away from their Infinity line and don’t have as many attachments as they used to. |
| FringeSport 2×3 attachments | – Mammoth Belt Squat – Safety Spotter Arms – Dip Station – Plate Storage – Landmine | |
| Synergee Fitness attachments | – Plate Storage – Landmine – Safety Arms – J-Cups |
Sunny Health & Fitness Power Zone Power Cage
No other brands match this size. The attachments in the 2×3, 5/8″ peg section above should fit this rack well enough.
| Attachments List | Popular | Notes |
|---|---|---|
| Mikolo Fitness attachments | – Lateral Raise – Lateral Raise & Chest Fly – Magnetic Hitch Pins | Look for 2×3 compatibility in the product descriptions. |
Rep Fitness PR-3000 (discontinued)
Griffin Fitness GR3 Lite, Rep Fitness PR-4000, Titan X-3, Vulcan Flat Base Power Rack
Slightly smaller than 3″x3″, and pegs slightly larger than 5/8″. Generally compatible with 3×3 racks with 5/8″ peg holes except for attachments using a second hole, because of the metric hole spacing.
| Attachments List | Popular | Notes |
|---|---|---|
| Rep Fitness PR-4000 attachments | – ISO Arms – Dip Attachment – Sandwich J Cups – Weight Storage – Landmine | |
| Titan Fitness X-3 attachments >> Amazon prices are lower in some cases. | – Adjustable Lever Arms – Safety Straps – Spotter Arms – Dip Attachment – Roller J Hooks | |
| Griffin Fitness GR3 Lite attachments | – Monolift – Dip Attachment – Adjustable Lever Arms | Look for ones with “GR3 Lite” in the title. |
| Vulcan Strength attachments | – Spotter Straps – Dip Horn – Plate Storage | Look for ones with “Flat Foot Power Rack” in the title. |
Rogue Monster Lite, Stray Dog Strength, Bells of Steel Hydra, Body Solid GPR400 / SPR500 / SPR1000*, Granite Fitness
* The Body Solid SPR1000 takes 5/8″ pegs facing the front/back, and 3/4″ pegs on the sides. Many of its attachments are made to fit the side holes, which are incompatible with any other racks.
| Attachments List | Popular | Notes |
|---|---|---|
| Rogue Monster Lite attachments | – Mutant Metals Ultimate Dip Attachment – Velocidor – Pritchett Pad – Sandwich J-Cups – Ghost Roller J-Cups | |
| Bells of Steel Hydra strength attachments Bells of Steel Hydra storage attachments | – Shoulder Boulder / Chest Fly – Leg Curl / Leg Extension – Seal Row Pad – Lever Arms – Y-Dip | Look for the Hydra size option on each product page. |
| Synergee Fitness attachments | – Plate Storage – Landmine – Safety Arms | |
| Stray Dog Strength attachments | – Alpha Single Utility Roller – GOAT – Utility Loop | Select the 5/8″ size. |
Mark Buffalo wrote a guide on how to fit the Titan X-3 lat pulldown on a Rogue Monster Lite rack.
American Barbell power racks, elitefts R3 / Collegiate / ISO
See the 3×3, 5/8″ section above for more attachments that will fit these racks well enough.
| Attachments List | Popular | Notes |
|---|---|---|
| American Barbell attachments | – Multi-Use Pin – Sandwich J Hooks – Dip Bar – Landmine | |
| elitefts attachments | – Dual Roller – Standing Leg Curl – Slider Monolift – Single Leg Squat – Jammer Arms |
Titan’s TITAN Series, Rep Fitness PR-5000, Vulcan Strength Racks (most), Griffin Fitness GR3, Giant Lifting 3X Series, Fringe Sport Osprey Power Cage / 3×3 rig, Get Rx’d RX3 / Goliath rack (discontinued), Fray Fitness Savage Series (out of business)
Slightly smaller than 3″x3″, and pegs slightly smaller than 1″. Generally compatible with 3×3 racks. The attachments here with a locking pin using a second hole, such as spotter arms, can even sometimes fully fit on 3×3 racks because the smaller peg size somewhat makes the attachment drop a little lower and reach the slightly wider spaced hole to lock into.
An exception: There have been reports of Titan’s regular J-hooks not fitting over 3×3 tubing.
| Attachments List | Popular | Notes |
|---|---|---|
| Rep Fitness 5000 Series attachments | – Strap Safeties – Dip Station – Landmine – ISO Arms – Spotter Arms | |
| Fringe Sport 3×3 attachments | – Mammoth Belt Squat – Weight Storage – Spotter Arms | |
| Get Rx’d RX3 attachments | – Dip Horn – Spotter Arms | |
| Titan Fitness TITAN Series attachments >> Amazon prices are lower in some cases. | – Safety Strap Spotters – Wrist Roller – Roller J Hooks – Dumbbell Holders – Weight Plate Storage | |
| Giant Lifting 3X attachments (use code TWOREP for 5% off) | – Mag Pin – Landmine – Dip Station | |
| Griffin Fitness GR3 attachments | – Monolift – Dip Attachment – Sandwich J Cups | Look for ones with “GR3” in the title or don’t specify. The “GR3 Lite” is a smaller size. |
Rogue Monster, Valor rig, Legend Fitness Performance Series, elitefts Origin Power Rack / Force Power Rack / Scholastic Half Racks / Garage Power Racks / Quick Ship Power Rack, Sorinex XL Series / Base Camp Series / Dark Horse, Bells of Steel Manticore, Bolt Fitness Storm Series, PRx Pro, Prime Prodigy, Inspire Fitness FPC1, Stray Dog Strength, Oak Club Manufacturing, Irwin Fitness, Ethos Power Rack 1.0 (discontinued), Amstaff Vortex Squat Rack / Summit Power Rack , Mikolo Fitness Anubis, Xmark Commercial / Viper, Crestone Rack / 370 (discontinued)
| Attachments List | Popular | Notes |
|---|---|---|
| Rogue Monster attachments | – Mutant Metals Ultimate Dip Attachment – Velocidor – Pritchett Pad – Adjustable Monolift – Ghost Roller J-Cups | |
| Bells of Steel strength attachments Bells of Steel weight storage attachments | – Shoulder Boulder / Chest Fly – Leg Curl / Leg Extension – Seal Row Pad – Lever Arms – Y-Dip | Look for the Manticore size option in the product descriptions. |
| Synergee Fitness attachments | – Plate Storage – Landmine – Safety Arms | |
| Sorinex attachments | – Sandwich J Hooks – Bulldog Pad – Jammer Arms – Leg Curl – Wrist Roller | Look for a fit of 1″ holes in the product descriptions. |
| Mikolo Fitness attachments | – Lateral Raise – Lateral Raise & Chest Fly – Magnetic Hitch Pins | Look for 3×3 in the titles or descriptions. |
| Legend Fitness Performance Series attachments | – Dip Attachment – Dual Landmine – Monster Hooks – Safety Arms – Plate Storage | Order by quote process only. |
| Oak Club Manufacturing attachments | – Magpin – Alpha Safety Arms – Klo Step Platform – Jay-M Short Bar Rack – James J Cups | |
| elitefts 3×3 attachments | – Dual Roller – Standing Leg Curl – Slider Monolift – Jammer Arms – Dip Attachment | They mainly use holes on the sides of the uprights, not front, so can be incompatible with other brands. Also look for the 1″ size in the product descriptions. |
| Prime Fitness Prodigy attachments | – Weight Plate Storage – Spotter Arms – Landmine | |
| Stray Dog Strength attachments | – Alpha Single Utility Roller – GOAT – Utility Loop | Select the 1″ size. |
For a high and low cable system that works on almost any power rack, see the Spud Inc Pulley System shown above.
If you only need a high pulley (for lat pulldowns and tricep pushdowns), see Giant Lifting’s pulley system for a much lower price.
This Rep Fitness dip station above fits on almost any rack with 1″ round safety bars (thanks Anthony!). The rack needs to have at least 21″ depth between the front and back uprights, which is the case for all freestanding racks and most floor-mounted racks except the most shallow ones. The rack’s hole spacing does not matter, as the bottom part of the attachment simply rests against wherever the lower safety bar is.
There are a couple solutions for power rack strap safeties if you can’t find a match. If you can get a brand of them with brackets that fit your rack but the straps are the wrong length, get two 2″ Stren-Flex slings of the right length to replace them with. They are extremely strong, with pertinent info labeled and a chart on that webpage with the pound ratings.
Your second option is a pair of Spud Inc suspension straps that hang off your rack’s top crossmembers.
Multiple questions on this in the comments prompted me to add this section.
You generally can’t add a rear rack extension – usually to accommodate weight plate storage – made for a different brand. The height of the holes off the floor and the rack width would have to be precisely the same.
Similarly, with extension feet meant to stabilize a rack, the holes would have to be precisely the same height off the floor, or they would float and defeat the purpose.
I have heard reports of people using these across brands, but in every case it seems the user made some modifications to make it work.
For the best compatibility going forward, I highly recommend getting a 3×3 rack taking 5/8″ pegs (Rogue Monster Lite compatible) or 1″ pegs (Rogue Monster compatible). Even you never buy a Rogue product, they lead the way in things like this.
Rogue appears to be de-emphasizing their 2×3 racks in favor of 3×3. Other manufacturers have seemed to follow suit. This doesn’t mean that nobody will make racks with 2×2 or 2×3 tubing. I believe that there will be a market for those lighter and cheaper racks for a long time, and they are not necessarily bad racks. The 3×3 attachments sell much better and are more numerous, because people who spend the extra money for a 3×3 rack are more likely to soup it up.
You might want to steer clear of racks that have metric sized tubing. They are harder to fit attachments on. Some of them fit ok.
View Comments
I purchased a Titan T-2 Rack with the Lat attachment and was notified by Titan that it is back ordered (additional 4 weeks) but could be longer. I researched the REP Fitness PR-1100 and their Lat attachment is very similar. Does anybody know if these attachments can be bolted directly to one one another rack system?
I'm not sure how accurate this list is, just tried to use a rep landmine for the 4000 series on a monster lite rack and it's no where near big enough.
If that's the inside of the landmine bracket you're measuring, that looks too tight to even fit on the 75mm Rep tubing. I don't suppose it's bent in or badly welded? Is it wider near the base?
It actually looks to be a 1/16th of inch or so narrower at the base. I had success attaching it via the side mount method as show in this attachment. Seems less supported but I think it will work.
Does anyone have any idea who made my rack? I bought it from someone a few years ago and love it but I would love to find accessories. Verticals are roughly 3”x2”, the holes are 1 3/4” holes, the posts are 1 1/2”, and 1 3/4”spaces in between.
Hi I am torn between the body solid GPR 400 or Rogue R3. I know, two differen racks. If decided for gpr400, could use rogue monster lite attachments. I think gpr have different size holes in the side. Thank you
Damn, I have a Northern Lights Power Rack (2×2 TUBING, 5/8″ PEGS) and can find no attachments anywhere... Any recommendations there (other than what you mentioned above)?
Elitefts offers a rack with that post size as well.
Can anyone confirm if the X-3 adjustable lever arms from Titan will be compatible with the Rogue Monster Lite Rack ?
These lever arms work just fine on my rep PR 4000.
What about Eleiko racks?
Hi David,
Do you have actual experience using attachments made for 3x3 with 5/8 pegs on a 3x3 with 3/4 peg rack? Might be buying an american barbell rack but want to make sure i can still use rogue, rep, and titan attachments later on
I can vouch for the compatibility of the x-3 and rep pr-4000 uprights. I have a flat foot titan x-3 but I needed an extension to fit my lat pulldown attachment. I got the pr-4000 uprights (solely to add some color and they were in stock while titan wasn’t) for stacking my weights and to attach my titan lat pull down attachment. I also got a flat foot extension kit from titan without the uprights that was on sale. I am happy to say they fit perfectly after a few modifications to the set up.
What modifications did you make?
Not much actually:
I put the pr-4000 upright on top of the base bar of the flat foot rack. The part of the base jutting out was facing out.
Everything else aligned. Will attach a pic soon.
I have a Parabody 814 rack and now my boys old enough and lifting, with 3 of us looking for attachments so this article has been amazing and I have bought a few and they fit perfectly THANKS! However, do you know if anyone makes an extension that will fit for instance the T2 extension?