2026 Update – Revamped entire guide to link to manufacturer pages that list all compatible attachments, so that you can quickly browse the full selections.
You get a hold of a great power rack or squat rack, but then you find out that the company doesn’t make the attachments / accessories that you want.
No problem! You should be able to find a compatible attachment or accessory, as long as your rack is made with one of a few standard configurations.
Table of Contents
The key specs are:
The tubing size of the uprights, as above, typically one of: 2″x2″, 2″x3″, or 3″x3″.
Racks made in China usually use metric sizing. This applies to a lot of brands featured here. They don’t advertise the fact, and you would have to ask them or run into the problem yourself. The tables they are organized in identify them as such.
The hardware/peg diameter that fits into the holes in the uprights, as above. Varies from 1/2″ to 1″. Going by the peg diameter is more consistent across brands than the hole size that is cut somewhat larger than the peg.
The hole spacing in the uprights, ie: the distance between holes on center, as above. This is only applicable for attachments that use 2 holes, the second using a locking pin.
2″ spacing is becoming the standard. Some racks have Westside spacing, which is 1″ spacing at a certain height range for setting bench press safety bars just right, and otherwise 2″ spacing above and below that.
An attachment can fit in a larger hole than it’s made for, but it will be able to wiggle and maybe tip down a little, depending on the snugness of the bracket that goes over the tubing.
Similarly, attachment brackets can fit onto slightly smaller tubing than what they were designed for. This can be less bad than the wrong peg size, because you can glue shims (UHMW plastic or wood) to the inside of the attachment’s bracket to make it fit. Some attachments work well enough even if they’re loose. Some don’t have enough pressure put on them to be a safety issue, like a battle rope anchor, but it could still rattle.
Lastly, the steel gauge (wall thickness) of rack tubing does not factor into compatibility. The tubes are fabricated to an outside diameter spec.
For fitting 3×3 attachments onto 2×3 tubing, or 2×3 attachments onto 2×2 tubing, an Etsy seller is making these adapters to fill the void in the bracket.
I don’t recommend you use load-bearing attachments that don’t fit quite right, such as J-hooks, steel safety arms, or plate holders, unless you have a good way of retrofitting it to be snug enough. Use some common sense, visualize it, and you’ll get the idea.
In many cases attachments that use a locking pin to secure the attachment into a second hole on the rack’s upright won’t line up the same on all racks. Normally this is the difference in metric and imperial (inches) hole spacing. As much as you want it to work, under most circumstances you won’t get the locking pin in. The offset starts at 1/16″ per hole and widens cumulatively.
If you’re thinking of foregoing the locking pin or buying a thinner one, and you have to ask for confirmation on whether it’s safe, you probably shouldn’t do it.
Rogue has among the best and most consistent quality. Cheap Amazon-only brands are the worst and might be unsafe, and we avoid promoting them when possible. Most other brands are somewhere in the middle or sometimes as good as Rogue.
Size categories ordered smallest to largest.
Titan X-2 (discontinued)
Discontinued size. The Titan T-3 Multi Grip Pull Up Bar is compatible with this rack (thanks TJ!).
Granite Fitness Series 22 racks (discontinued)
Powerline PPR1000, Northern Lights Crossbox (discontinued)
| Attachments List | Popular | Notes |
|---|---|---|
| Powerline attachments | – U-Link / Rope Anchor – T-Bar Row Attachment / Landmine – Weight Plate Horn | See the Options links on the PPR1000 product page. They aren’t organized well anywhere else. |
Titan Fitness T-2, Giant Lifting 2X Series
50mm is a hair smaller than 2″. These are generally compatible with 2×2 racks. However, 2×2 attachments using a second hole and hitch pin are incompatible.
This size is considered a “budget” rack, so there are typically only a few attachments.
| Attachments List | Popular | Notes |
|---|---|---|
| Titan T-2 Series attachments >> Amazon prices are lower in some cases. | – Landmine – Spotter Arms – Dip Bars – Weight Plate Holders | |
| Giant Lifting 2X Series attachments (use code TWOREP for 5% off) | – Mag Pins – Landmine – J Cups |
Powerline PPR200X / PPR500, Best Fitness BFPR100, Valor BD-7 / BD-33, Rep Fitness PR-1000 / PR-1050 / PR-1100, Fringe Garage Series Squat Cage, Legend Fitness Varsity Series, Get Rx’d Pro Power Cage, Vanswe Power Rack, TDS 1000lb Power Squat Rack, Fitness Reality 810XLT, Mikolo Fitness F4 / K6, Amstaff PR100 / DF1161A / TP006D (discontinued)
This size is considered a “budget” rack, so there are typically only a few attachments, and some manufacturers don’t seem to offer any.
| Attachments List | Popular | Notes |
|---|---|---|
| Rep Fitness PR-1000 Series attachments | – Spotter Arms – Weight Storage – Dip Station – Landmine – Sandwich J Cups | |
| Fringe Garage Series attachments | – Mammoth Belt Squat – Weight Storage – Spotter Arms | |
| Synergee Fitness attachments | – Plate Storage – Safety Arms – Dip Handles | |
| Valor BD-7/BD-33 attachments | – Dip Handles – Spotter Arms – Weight Plate Storage | |
| Mikolo Fitness attachments | – Lateral Raise – Leg Extension & Curl – Lateral Raise & Chest Fly – Magnetic Hitch Pins | Look for 2×2 in the title. |
ForceUSA MyRack only.
60mm is 2.36″, way off from all imperial sized racks. These attachments might fit the metric racks in the next section well enough that take 16mm pegs.
| Attachments List | Popular | Notes |
|---|---|---|
| MyRack attachments | – Safety Slings – Monolift – Dip Handle – J Hooks Pro – Landmine |
Bells of Steel Residential Rack / Utility Rack / Light Commercial Rack / Brute Rack / Folding Rack / Combo Rack
60mm is 2.36″, way off from all imperial sized racks. Some attachments in the 13mm peg section above might fit well enoough.
| Attachments List | Popular | Notes |
|---|---|---|
| Bells of Steel strength attachments Bells of Steel weight storage attachments | – Seal Row Pad – Y-Dip – Spotter Arms – Landmine – Sandwich J Cups | Look for the 2.3″ size option on the product pages. |
Powertec WB-PR / P-PR (discontinued), Hulkfit Power Cage
60mm is 2.36″, way off from all imperial sized racks.
| Attachments List | Popular | Notes |
|---|---|---|
| Powertec attachments | – Premium J Hooks – Spotter Arms – Weight Storage | Look for ones that fit 2 3/8″ uprights per the product descriptions. |
Valor BD-11 / BD-41, Amstaff TR023 (discontinued) / TR025 (discontinued) / SD1050 (discontinued)
| Attachments List | Popular | Notes |
|---|---|---|
| Valor BD-11/BD-41 attachments | – Dip Handles – Spotter Arms – Weight Storage |
Titan Fitness T-3 / T-6 (discontinued)
Slightly smaller than 2″x3″, and pegs slightly larger than 5/8″. Generally compatible with 2×3 racks except for attachments using a second hole, because of the metric hole spacing.
| Attachments List | Popular | Notes |
|---|---|---|
| Titan T-3 attachments >> Amazon prices are lower in some cases. | – Safety Spotter Arms – Safety Straps – Safety Strap Spotter Arms – Dip Bars – Weight Plate Holders | |
Rogue Infinity (R-Series), FringeSport Kip Power Cage / 2×3 rigs (discontinued), Bolt Fitness Lightning Power Racks, Synergee Fitness 2300 Series
| Attachments List | Popular | Notes |
|---|---|---|
| Rogue Infinity attachments | – Speed Bag Platform – Battle Rope Anchor – Matador – Spotter Arms | They have focused away from their Infinity line and don’t have as many attachments as they used to. |
| FringeSport 2×3 attachments | – Mammoth Belt Squat – Safety Spotter Arms – Dip Station – Plate Storage – Landmine | |
| Synergee Fitness attachments | – Plate Storage – Landmine – Safety Arms – J-Cups |
Sunny Health & Fitness Power Zone Power Cage
No other brands match this size. The attachments in the 2×3, 5/8″ peg section above should fit this rack well enough.
| Attachments List | Popular | Notes |
|---|---|---|
| Mikolo Fitness attachments | – Lateral Raise – Lateral Raise & Chest Fly – Magnetic Hitch Pins | Look for 2×3 compatibility in the product descriptions. |
Rep Fitness PR-3000 (discontinued)
Griffin Fitness GR3 Lite, Rep Fitness PR-4000, Titan X-3, Vulcan Flat Base Power Rack
Slightly smaller than 3″x3″, and pegs slightly larger than 5/8″. Generally compatible with 3×3 racks with 5/8″ peg holes except for attachments using a second hole, because of the metric hole spacing.
| Attachments List | Popular | Notes |
|---|---|---|
| Rep Fitness PR-4000 attachments | – ISO Arms – Dip Attachment – Sandwich J Cups – Weight Storage – Landmine | |
| Titan Fitness X-3 attachments >> Amazon prices are lower in some cases. | – Adjustable Lever Arms – Safety Straps – Spotter Arms – Dip Attachment – Roller J Hooks | |
| Griffin Fitness GR3 Lite attachments | – Monolift – Dip Attachment – Adjustable Lever Arms | Look for ones with “GR3 Lite” in the title. |
| Vulcan Strength attachments | – Spotter Straps – Dip Horn – Plate Storage | Look for ones with “Flat Foot Power Rack” in the title. |
Rogue Monster Lite, Stray Dog Strength, Bells of Steel Hydra, Body Solid GPR400 / SPR500 / SPR1000*, Granite Fitness
* The Body Solid SPR1000 takes 5/8″ pegs facing the front/back, and 3/4″ pegs on the sides. Many of its attachments are made to fit the side holes, which are incompatible with any other racks.
| Attachments List | Popular | Notes |
|---|---|---|
| Rogue Monster Lite attachments | – Mutant Metals Ultimate Dip Attachment – Velocidor – Pritchett Pad – Sandwich J-Cups – Ghost Roller J-Cups | |
| Bells of Steel Hydra strength attachments Bells of Steel Hydra storage attachments | – Shoulder Boulder / Chest Fly – Leg Curl / Leg Extension – Seal Row Pad – Lever Arms – Y-Dip | Look for the Hydra size option on each product page. |
| Synergee Fitness attachments | – Plate Storage – Landmine – Safety Arms | |
| Stray Dog Strength attachments | – Alpha Single Utility Roller – GOAT – Utility Loop | Select the 5/8″ size. |
Mark Buffalo wrote a guide on how to fit the Titan X-3 lat pulldown on a Rogue Monster Lite rack.
American Barbell power racks, elitefts R3 / Collegiate / ISO
See the 3×3, 5/8″ section above for more attachments that will fit these racks well enough.
| Attachments List | Popular | Notes |
|---|---|---|
| American Barbell attachments | – Multi-Use Pin – Sandwich J Hooks – Dip Bar – Landmine | |
| elitefts attachments | – Dual Roller – Standing Leg Curl – Slider Monolift – Single Leg Squat – Jammer Arms |
Titan’s TITAN Series, Rep Fitness PR-5000, Vulcan Strength Racks (most), Griffin Fitness GR3, Giant Lifting 3X Series, Fringe Sport Osprey Power Cage / 3×3 rig, Get Rx’d RX3 / Goliath rack (discontinued), Fray Fitness Savage Series (out of business)
Slightly smaller than 3″x3″, and pegs slightly smaller than 1″. Generally compatible with 3×3 racks. The attachments here with a locking pin using a second hole, such as spotter arms, can even sometimes fully fit on 3×3 racks because the smaller peg size somewhat makes the attachment drop a little lower and reach the slightly wider spaced hole to lock into.
An exception: There have been reports of Titan’s regular J-hooks not fitting over 3×3 tubing.
| Attachments List | Popular | Notes |
|---|---|---|
| Rep Fitness 5000 Series attachments | – Strap Safeties – Dip Station – Landmine – ISO Arms – Spotter Arms | |
| Fringe Sport 3×3 attachments | – Mammoth Belt Squat – Weight Storage – Spotter Arms | |
| Get Rx’d RX3 attachments | – Dip Horn – Spotter Arms | |
| Titan Fitness TITAN Series attachments >> Amazon prices are lower in some cases. | – Safety Strap Spotters – Wrist Roller – Roller J Hooks – Dumbbell Holders – Weight Plate Storage | |
| Giant Lifting 3X attachments (use code TWOREP for 5% off) | – Mag Pin – Landmine – Dip Station | |
| Griffin Fitness GR3 attachments | – Monolift – Dip Attachment – Sandwich J Cups | Look for ones with “GR3” in the title or don’t specify. The “GR3 Lite” is a smaller size. |
Rogue Monster, Valor rig, Legend Fitness Performance Series, elitefts Origin Power Rack / Force Power Rack / Scholastic Half Racks / Garage Power Racks / Quick Ship Power Rack, Sorinex XL Series / Base Camp Series / Dark Horse, Bells of Steel Manticore, Bolt Fitness Storm Series, PRx Pro, Prime Prodigy, Inspire Fitness FPC1, Stray Dog Strength, Oak Club Manufacturing, Irwin Fitness, Ethos Power Rack 1.0 (discontinued), Amstaff Vortex Squat Rack / Summit Power Rack , Mikolo Fitness Anubis, Xmark Commercial / Viper, Crestone Rack / 370 (discontinued)
| Attachments List | Popular | Notes |
|---|---|---|
| Rogue Monster attachments | – Mutant Metals Ultimate Dip Attachment – Velocidor – Pritchett Pad – Adjustable Monolift – Ghost Roller J-Cups | |
| Bells of Steel strength attachments Bells of Steel weight storage attachments | – Shoulder Boulder / Chest Fly – Leg Curl / Leg Extension – Seal Row Pad – Lever Arms – Y-Dip | Look for the Manticore size option in the product descriptions. |
| Synergee Fitness attachments | – Plate Storage – Landmine – Safety Arms | |
| Sorinex attachments | – Sandwich J Hooks – Bulldog Pad – Jammer Arms – Leg Curl – Wrist Roller | Look for a fit of 1″ holes in the product descriptions. |
| Mikolo Fitness attachments | – Lateral Raise – Lateral Raise & Chest Fly – Magnetic Hitch Pins | Look for 3×3 in the titles or descriptions. |
| Legend Fitness Performance Series attachments | – Dip Attachment – Dual Landmine – Monster Hooks – Safety Arms – Plate Storage | Order by quote process only. |
| Oak Club Manufacturing attachments | – Magpin – Alpha Safety Arms – Klo Step Platform – Jay-M Short Bar Rack – James J Cups | |
| elitefts 3×3 attachments | – Dual Roller – Standing Leg Curl – Slider Monolift – Jammer Arms – Dip Attachment | They mainly use holes on the sides of the uprights, not front, so can be incompatible with other brands. Also look for the 1″ size in the product descriptions. |
| Prime Fitness Prodigy attachments | – Weight Plate Storage – Spotter Arms – Landmine | |
| Stray Dog Strength attachments | – Alpha Single Utility Roller – GOAT – Utility Loop | Select the 1″ size. |
For a high and low cable system that works on almost any power rack, see the Spud Inc Pulley System shown above.
If you only need a high pulley (for lat pulldowns and tricep pushdowns), see Giant Lifting’s pulley system for a much lower price.
This Rep Fitness dip station above fits on almost any rack with 1″ round safety bars (thanks Anthony!). The rack needs to have at least 21″ depth between the front and back uprights, which is the case for all freestanding racks and most floor-mounted racks except the most shallow ones. The rack’s hole spacing does not matter, as the bottom part of the attachment simply rests against wherever the lower safety bar is.
There are a couple solutions for power rack strap safeties if you can’t find a match. If you can get a brand of them with brackets that fit your rack but the straps are the wrong length, get two 2″ Stren-Flex slings of the right length to replace them with. They are extremely strong, with pertinent info labeled and a chart on that webpage with the pound ratings.
Your second option is a pair of Spud Inc suspension straps that hang off your rack’s top crossmembers.
Multiple questions on this in the comments prompted me to add this section.
You generally can’t add a rear rack extension – usually to accommodate weight plate storage – made for a different brand. The height of the holes off the floor and the rack width would have to be precisely the same.
Similarly, with extension feet meant to stabilize a rack, the holes would have to be precisely the same height off the floor, or they would float and defeat the purpose.
I have heard reports of people using these across brands, but in every case it seems the user made some modifications to make it work.
For the best compatibility going forward, I highly recommend getting a 3×3 rack taking 5/8″ pegs (Rogue Monster Lite compatible) or 1″ pegs (Rogue Monster compatible). Even you never buy a Rogue product, they lead the way in things like this.
Rogue appears to be de-emphasizing their 2×3 racks in favor of 3×3. Other manufacturers have seemed to follow suit. This doesn’t mean that nobody will make racks with 2×2 or 2×3 tubing. I believe that there will be a market for those lighter and cheaper racks for a long time, and they are not necessarily bad racks. The 3×3 attachments sell much better and are more numerous, because people who spend the extra money for a 3×3 rack are more likely to soup it up.
You might want to steer clear of racks that have metric sized tubing. They are harder to fit attachments on. Some of them fit ok.
View Comments
Is it confirmed that the Titan T-3 lever arms fit the Rogue infinity racks? I haven't seen a lot of info on the cross-compatibility, and much of it is conflicting.
hi, i have spare Rogue Monster 2.0 upright and been thinking to convert it to kind of all-in-one storage for Dumbbell & Miscellanous stuff.. does Stray Dog Strength dumbbell Tray and or crossmember will fit on Rogue Monster 2.0 upright?
thanks in advance.
Will sorinex jammer arns work on a rogue monster rack. Both 3x3
Anyone have any clue if a Rep Fitness crossmembers will fit on Rogue Monster uprights? I worry about the hole spacing not lining up exactly right before ordering small crossmembers to downsize the depth of my rack.
Hi, did you ever see if the Rep cross members fit Rogue? Thanks!
They should. Rogue monster is 1" spacing , rep PR-5000 is also 1" space
Excellent article and very informative! Thanks for the great work!
Question: Does the diameter size refer to the hole or the hardware/peg?
For example, is:
a) the hole 5/8" and the peg is smaller like 9/16" OR
b) the peg 5/8" and the hole is larger like 11/16"
Background: I'm starting to think the holes on my squat rack were cut too small for a few reasons.
1) I purchased spotter arms from the same company and the pegs didn't fit into the holes on the squat rack
2) I purchased an attachment from a separate company that is included in above chart and the pegs also didn't fit
3) The product page has this strange note: "***Note: These replacement J-Cups will not fit Garage Series Squat Racks with Pull Up Bar ordered between June 2020 and October 2020. Please contact team@fringesport.com to place an order for j-cups if you ordered during this timeframe***". I purchased my squat rack just after the period.
Anyone else run into this?
The charts are the hardware or peg size. Holes are a varying amount bigger. It sounds like your interpretation is right and Fringe made an incompatible rack that you got caught in despite the date. This is the first I've heard of it.
I've run into the same issue with https://www.fringesport.com/collections/squat-racks/products/floor-mounted-kip-cage
this 2x3 rack has holes which I measured at
2" side are .6225"
3" side are .6715"
which makes the front-facing holes slightly too small for 5/8 (.625) attachments. I contacted Fringe if this was intentional as it seems strange the 2" side and 3" side holes were different, but no answer as to why this is... J-cups were out of stock at the time and not luck with an alternative.
Looking for safety spotter straps that fit a body solid Gpr400
Ditto that question. Im also looking for safety straps that works on the GPR400 So if you or anybody else finds a good solution, please post here.
Answering myself. I bought the "säkerhetsarmar" from Gymkompaniet in Sweden. They have a danish site as well. The spotter arms are made for their Recoil racks. But it fit nicely at a very competitive price.
Hi, I've looked everywhere trying to find someone to validate that the rogue monster shrimp trawler will fit onto a Rep PR-5000v2 rack. I'm trying to mount my heavy bag to the rack. the hole spacing issue (1.96" vs 2") is a bit concerning because the shrimp trawler's holes are spaced 6" apart, center to center. That's now a difference of of 0.12" over the 6" (0.04" * 3 = 0.12"). Has anybody put this configuration together?
You can buy a shrimp trawler from titan or bolt fitness, and be sure it's metric spacing.
So I decided to take a chance on the Rogue Monster Shrimp Trawler. I figured worst case I will drill out the holes a bit to make it fit. I was pleasantly surprised to find that the holes in the shrimp trawler are not round, but oval and will easily accommodate attachment to a Rep rack. Plus it has three holes, but Rogue confirmed you only need to use two of the holes (they only give you two bolts anyway). I've attached a pic of the trawler. I'm trying to get Rep to sell me a single 16" crossmember that I will then mount on the top of the rack in a vertical position and attach the trawler to it. this will allow me to get it higher so the bag hangs at the right height.
Hey Chris, I'm trying to do exactly what you are doing. Did rep sell you the cross members? If so, I'd love to see a picture of the final product.
Regards,
Mark
Mark, so they did sell me a set of two (apparently i couldn't buy just one). it's the Apollo 16" crossmember
https://repfitness.com/collections/rack-attachments/products/apollo-16-crossmembers
if you look closely, the shrimp trawler is leaning down. it's not bending, it's caused by the play in the holes vs the bolt. the heavy bag (just 100lb) and the trawler are pulling laterally on the crossmember and it's twisting in the holes. if you have a 93" upright, you could mount the trawler directly to the upright and there wouldn't be a problem. Functionally i don't think it's a problem.
One thing that I didn't expect is that hitting the bag causes the rack to shake (i'm not that strong). i put spring clips on the weight horns to keep the smaller weights from vibrating off. i don't have it bolted to the floor as i have about 1000 lbs of weight plates on it.
The cross-member is black metallic, so if you choose to do this, i make you a deal on the other cross-member ;)
you should try and add the monster mini feet to the sides where the bag is, according to Brandon from youtube channel, ill leave the link https://www.youtube.com/watch?v=j-mftvdU9Vc , he explains the feet from rogue https://www.roguefitness.com/rogue-monster-mini-feet should fit the pr 5000 series and vice versa. I am trying to do the same as well add a bag to my pr 5000, the mini feet are only 13 inches long and should help in making sure the rack is stable, while also making sure they are not on the way.
so the rogue mini-feet came in, but unfortunately they would only mount to the front. they will not mount to the side where the trawler is. I wanted to like them, but I ended up sending them back since they weren't going to really help lateral stability. I'll probably mount a bar hanger on the opposite side to offset some of the weight.
Just notice the holes on the pr 5000 are higher than the ones on the front, did the feet fit the holes on holes or they just don't align with holes on the side?, If they do align with the side holes I might weld a piece of metal or put a piece of thick rubber between the feet and floor, why can rep just do all holes the same distance in all sides.
yeah it wasn't an issue with the mount height. like you said, i could very simply put some spacers under the foot to make the height issue go away. the problem was that the hole spacing didn't seem to line up at all on the side. very perplexing. It would definitely mount to the front if I wanted to do that.
thanks, i like those feet. i'll look at getting a set. i also revisited this setup and repositioned the pull-up bar between the two 16" uprights. this keeps the bag from pulling the crossmember and the setup seems a lot more stable when hitting the bag.
The Storm Series bolt "Accessory Hanger" looks like it would work! I'll give them a call. thanks!
Has anyone found a Lat/Row cable attachment compatible with the Ethos Power Rack 1.0? It looks as though a different cross member across the back would be necessary at the very least.
Both rear cross members have slotted bolt holes. So there's some flexibility in regards to installing it on a non titan rack. Worst case scenario you can always drill your rack. Bigger issue is the width of the cross members. If your rack is under 42" wide between the posts. You'll need to use spacers on your racks factory cross members/pullup bars. If it's greater, you'll need spacers on the titan cross members.
FYI,
I own a New (Oct 2021) Titan Series 100" tall 6 Post Power Rack and am using some new Rep PR 5000 Attachments (1" pegs with 2" Hole spacing). The pegs and holes line up perfectly with no modifications as follows;
Rep Standard and Lowered J Cups (Not available from Titan)
Rep PR 5000 24" Spotter Arms
Rep PR 5000 Front Foot Extensions (Not available from Titan)
Rep PR 5000 6 " Weight Horns (Not available from Titan)
Alternating the standard and lowered J cups allow 1" spacing for squats/benchesn etc.
The spotter arms and foot extensions allow use outside the front of the rack without having to bolt it down (This thing is a BEAST and will never move no matter how heavy I go anyhow)... ;-)
I have spent three days trying to figure out the same and chanced upon this site! This is awesome and helps in figuring out which way to go. Bravo!